Influence of the Wall Thickness Value on the Cross Wall Thickness Deviation of Tubes Rolled on the Tube Rolling Plant with the Continuous Mill | Journal of Engineering Sciences

Influence of the Wall Thickness Value on the Cross Wall Thickness Deviation of Tubes Rolled on the Tube Rolling Plant with the Continuous Mill

Author(s): Pilipenko S. V.*, Drozhzha P. V., Limonchenko E. A.

Affilation(s): National Metallurgical Academy of Ukraine, 4 Gagarina Av., Dnipro, 49600, Ukraine

*Corresponding Author’s Address: 44-08@i.ua

Issue: Volume 5; Issue 1 (2018)

Dates:
Paper received: January 12, 2018
The final version of the paper received: February 12, 2018
Paper accepted online: March 5, 2018

Citation:
Pilipenko S. V. Influence of the wall thickness value on the cross wall thickness deviation of tubes rolled on the tube rolling plant with the continuous mill / S. V. Pilipenko, P. V. Drozhzha, E. A. Limonchenko // Journal of Engineering Sciences. – Sumy : Sumy State University, 2018. – Volume 5, Issue 1. – P. A8-A11.

DOI: 10.21272/jes.2018.5(1).a2

Research Area: MANUFACTURING ENGINEERING: Machines and Tools

Abstract. The high requirements as to accuracy of the wall thickness are due not only to necessity of assuring the reliability and serviceability of equipment, but also to the trend towards the continuous decrease of metal capacity. In this situation assuring observing of the given parameter is the most difficult affair. The cross wall thickness deviation can be presented in the form of two components: eccentric and symmetric deviation. In the given work authors present the research of the influence of the tube wall thickness on the share of eccentric component of the wall thickness deviation of the tubes rolled on the TRP with the continuous mill. Analysis of research results allowed concluding that with increase of the tube wall thickness the share of wall thickness deviation induced with the eccentricity decreases. On the whole, it is to be noted that for the giving plant, characteristically the influence of methods of longitudinal flaring (in continuous mill with mandrel and multistand mills of rolling without mandrel) on the tube accuracy is greater. In two first cases while reducing tubes to the finish dimension, the share of the number of faces, which depends on the summary reduction through the diameter and the value of tension, increases substantially.

Keywords: tube rolling plant with continuous mill, wall thickness, cross wall thickness deviation, eccentric component.

References:

  1. Stoletnij, M. F., Klempert, Ye. D. (1975). Tochnost’ trub. Moscow, Metallurgiya [in Russian].
  2. Vydrin, A. V., Shirokov, V. V. (2014). Teoreticheskiye osnovy povysheniya tochnosti razmerov trub pri prokatke na niepreryvnom stane. Vestnik Yuzhno-Uralskogo gosudarstvennogo Universiteta, Seriya “Metallurgiya. Sbornik nauchnykh trudov”, No. 14, 81–86 [in Russian].
  3. Khramkov, Ye. V., Shirokov, V. V. (2014). Otsenka vliyaniya razlichnykh faktorov na tochnost’ trub / Ye.V/ Khramkov, V.V. Shirokov // Vestnik Yuzhno-Uralskogo gosudarstvennogo Universiteta. Seriya: Metallurgiya. Sbornik nauchnykh trudov N 14. – YuUrGU: Cheliyabinsk, 2014. – S. 76-79 [in Russian].
  4. Struin, D. O. (2012). Issledovaniye tochnosti prokata na TPA so stanom PQF. Innovatsionnye teknologii v metallurgii i mashynostroyenii. A. F. Golovin Uralskaya nauchno-pedagogicheskaya shkola, pp. 499–501 [in Russian].

Full Text




Scientific journal "The Journal of Engineering Sciences"
ISSN 2312-2498 (Print), ISSN 2414-9381 (Online).

Faculty of Technical Systems and Energy Efficient Technologies
Sumy State University