Ensuring Accurate Characteristics of the Pipe-Piston Installation

Author(s): Denysenko Y. O.¹, Pop G. M.², Sushko V. V.³, Korniienko, A. O.¹, Husar I.²

Affiliation(s):
¹Sumy State University, University, 2, Rymskogo-Korsakova St., Sumy 40007, Ukraine;
² Technical University of Cluj-Napoca, 18, Memorandumului St., Cluj-Napoca 400114, Romania;
³ State Enterprise “Sumy Regional Scientific and Production Center for Standardization, Metrology and Certification”, 101, Kharkivska St., Sumy 40007, Ukraine

^*Corresponding Author’s Address: [email protected]

Issue: Volume 9, Issue 2 (2022)

Dates:
Submitted: April 11, 2022
Accepted for publication: August 28, 2022
Available online: September 3, 2022

Citation:
Denysenko, Y. O., Pop, G. M., Sushko V. V., Korniienko, A. O., Husar I. (2022). Ensuring accurate characteristics of the pipe-piston installation. Journal of Engineering Sciences, Vol. 9(2), pp. B1-B6, doi: 10.21272/jes.2022.9(2).b1

DOI: 10.21272/jes.2022.9(2).b1

Research Area: MANUFACTURING ENGINEERING: Technical Regulations and Metrological Support

Abstract. The study aims to increase the efficiency of the use of the pipe-piston unit by ensuring the reliability of the measurement results based on the development of calibrating technique for the pipe-piston installation. Theoretical research is based on using the principles of system and process approaches. To solve the scientific problem, the fundamental provisions of statistical methods and experimental methods were used; methods of mathematical modeling of estimation of measurement uncertainties. Based on the results of the work, the normative document “Metrology. Installations of a standard pipe-piston. Calibration technique”. The approach to controlling metrological characteristics of the pipe-piston installation, based on estimating the uncertainty of measurements during its calibration, was further developed. Application of the proposed approach allows one to control the metrological characteristics directly on site without disrupting the working product’s accounting process and increasing the pipe-piston installation’s efficiency by an increase in the reliability of measurements and ensuring repeatability.

Keywords: methods, calibration, pipe-piston installation, uncertainty, verification.

References:

Tai, B., Stephenson, D., Shih, A. (2011). Improvement of surface flatness in face milling based on 3-D holographic laser metrology. International Journal of Machine Tools & Manufacture, Vol. 51(6), pp. 483–490. doi: 10.1016/j.ijmachtools.2011.02.006.
Wu, W.G, Yu, Q.X., Chang, X., Pang, S.Q. (2004) Design Theory and Experiment of the Step Face Milling Cutter Based on Free Cutting. Advances in Grinding and Abrasive Processes, Vol. 259–2, pp. 132–136. doi: 10.4028/www.scientific.net/KEM.259-260.132
Ramakrishnan, S., Wysk, R. (2002) Optimization of The Length of Travel in Face Milling Operations for Flat Surfaces. Transactions of The North American Manufacturing Research Institute of SME, Vol. XXX, pp. 431–438.
Hadad, M., Ramezani, M. (2016) Modeling and analysis of a novel approach in machining and structuring of flat surfaces using face milling process. International Journal of Machine Tools and Manufacture, Vol. 05, pp. 32–44. doi: 10.1016/j.ijmachtools.2016.03.005
Ivanov, V., Dehtiarov, I., Pavlenko, I., Kosov, M., Hatala, M. (2020) Technological assurance and features of fork-type parts machining. Advances in Design, Simulation and Manufacturing II. DSMIE 2019. Lecture Notes in Mechanical Engineering, pp. 114–125. doi: 10.1007/978-3-030-22365-6_12
Taurit, G.E. (1981) Machining Large Parts. Tekhnika.
Kushnirov, P., Zhyhylii, D., Ivchenko, O., Yevtukhov, A., Dynnyk, O. (2020) Investigation of the dynamic state of adjustable milling heads. Advances in Design, Simulation and Manufacturing II. DSMIE 2019. Lecture Notes in Mechanical Engineering, Vol. II, pp. 169–179. doi: 10.1007/978-3-030-22365-6_17
Ivanov, V., Dehtiarov, I., Pavlenko, I., Kosov, I., Kosov, M. (2019) Technology for complex parts machining in multiproduct manufacturing. Management and Production Engineering Review, Vol. 10(2), pp. 25–36. doi: 10.24425/mper.2019.129566
Ivanov, V., Dehtiarov, I., Zaloga, V., Kosov, I., Savchuk, V. (2020) Increasing Productivity of Connecting Rods Machining. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds) Advances in Design, Simulation and Manufacturing III. DSMIE 2020. Lecture Notes in Mechanical Engineering, Vol. III, pp. 264–275. doi: 10.1007/978-3-030-50794-7_26
Hlembotska, L., Melnychuk, P., Balytska, N., Melnyk, O. (2018) Modelling the loading of the nose-free cutting edges of face mill with a spiral–stepped arrangement of inserts. Eastern Eur. J. Enterp. Technol, Vol. 1(91), pp. 46–54.
Lishchenko, N. V., Larshin, V. P., Pitel, J. (2020) Vibrational impact on milled surface irregularities. Journal of Engineering Sciences, Vol. 7(1), pp. A8–A16. doi: 10.21272/jes.2020.7(1).a2
Permyakov, A., Dobrotvorskiy, S., Dobrovolska, L., et al. (2019) Computer modelling application for predicting of the passing of the high-speed milling machining hardened steel. In: Ivanov, V., et al. (eds.) Advances in Design, Simulation and Manufacturing. DSMIE-2018. Lecture Notes in Mechanical Engineering, pp. 135–145. doi:10.1007/978-3-319-93587-4_15
Klimenko, S. (2017) Improvement of performance of ﬁnishing of details with a cutting tool. J. Zhytomyr State Technol. Univ Vol. 2(88), pp. 56–66.
Ivanov, V., Pavlenko, I. (2017) Comprehensive analysis of the mechanical system system “ﬁxture–workpiece”. Journal of Engineering Science, Vol. 4(1), pp. A1–A10.
Ivanov, V. (2018) Process-Oriented Approach to Fixture Design. In: Ivanov, V. et al. (eds) Advances in Design, Simulation and Manufacturing. DSMIE 2018. Lecture Notes in Mechanical Engineering, pp. 42–50. Springer, Cham. doi: 10.1007/978-3-319-93587-4_5.
Coromant, S.: Cutter path and chip formation in milling, https://www.sandvik.coromant.com/en-gb/knowledge/milling/pages/cutter-path-and-chip-formation.aspx, last accessed 15/05/2021.

Full Text